Tools You Need to Set Up a New Bathtub
Tools You Need to Set Up a New Bathtub
Blog Article
We have found this article on Installing A Bathtub directly below on the internet and concluded it made good sense to write about it with you here.
Setting up a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new tub in your shower room if you have actually currently gotten a brand-new tub as well as don't need to transform the setup of your previous water pipelines.
Your tools as well as material checklist should comprise the following:
Planning for the Setup
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, position the bath tub in the required setting. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the level reviews degree.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking a few minutes to browse our posting. Liked our blog entry? Please share it. Let someone else discover it. I enjoy reading our article about How to Install a Bathtub Yourself.
Schedule An Appointment
Report this page